Vybronics - one of largest suppliers of cylindrical & coin vibration motors



COVID has played havoc with production schedules and in some cases have caused production lines to shut down due to lack of a part(s) on the bill of material.     While Vybronics has not experienced any supply chain issues with our raw material vendors needed to manufacture our vibrations motors, some of our clients request […]


VC0625B001L thumbnail

6 mm x 2.5 mm | 2.5 V | Coin Vibration Motor

At  6mm, the VC0625B001L is the smallest diameter, brush type, coin vibration motor on the market. Its ideal for light weight wearable devices such as fitness trackers and smart watches. As this coin ERM vibration motor is relatively expensive, we recommend you use this motor only if your design cannot utilize one of our lower priced 8mm or 10mm diameter coin vibration motors.   Please note that this part DOES NOT have adhesive tape on the bottom.   If you need this, please order  VC0625B002L .  If you require a longer lead wire length, or connectors to be added, after sample approval, we require a 2000 pcs minimum order.


VC0625B002L thumbnail

6 mm x 2.5 mm | 2.5 V | Coin Vibration Motor

At  6mm, the VC0625B002L is the smallest diameter, brush type, coin vibration motor on the market. Its ideal for light weight wearable devices such as fitness trackers and smart watches. As this coin ERM vibration motor is relatively expensive, we recommend you use this motor only if your design cannot utilize one of our lower priced 8mm or 10mm diameter coin vibration motors.   Please note that this part has double stick (PSA) adhesive tape on the bottom of the motor case.  If you do not need this, please order  VC0625B001L .  If you require a longer lead wire length, or connectors to be added, after sample approval, we require a 2000 pcs minimum order.

 


VC0720B088L thumbnail

7 mm x 2.1 mm | 3 V | FPC | Coin Vibration Motor

The C0720B088L coin vibration motor has a unique interconnection method that greatly simplifies mass production.   The contact pads under the vibration motor mate with corresponding PCB mounted, ultra-small Spring Finger Contacts.  These spring contacts are available on tape /reels for easy SMD assembly.   This coin motor is typically mounted in a molded pocket of the device, and held in place by  the supplied double stick tape.  If this motor is too small, we can employ this solution with larger sized motors, however, tooling fees may apply.  


VC0820B006F thumbnail

8 mm x 2.1 mm | 3 V | Coin Vibration Motor

Measuring only 8 mm x 2 mm the VC0820B006F is our smallest diameter 8mm, brush type,  flat vibration motor. This motor is supplied with a self adhesive tape which can be used to secure the motor to your PCB or the inner wall of your products housing. It can be ordered without it if not needed for your application. This motor is available with wire leads, however, we can add on our standard connectors to the wire leads. If purchased in minimum lots of 10K pcs we can supply it with a custom FPC (flexible printed circuit). The FPC can be connected to your PCB by “hot bar soldering” or it can mate with pogo pins placed on your PCB.


VC0820B029L thumbnail

8 mm x 2.1 mm | 3 V | FPC | Pancake Vibration Motor

The VC0820B029L is a pancake vibration motor with FPC contact pads, and is based on the popular leaded version of the same motor, the VC0820B006F. This device is designed to be mounted in a molded recessed pocket in the products housing.   PCB mounted contact springs or pogo pings mate with coin LRA's contacts pads.   PCBA contact springs are made by TE as well as other companies.  


VC0825B002F thumbnail

8 mm x 2.5 mm | 3 V | Coin Vibration Motor

Our VC0825B002F coin vibration motor is ideal for both cellular or wearable applications. This motor is supplied with a self adhesive tape which can be used to secure the motor to your PCB or the inner wall of your products housing. It can be ordered without it if not needed for your application. As this motor is relatively expensive and we recommend you use this motor only if your design can not utilize one of our lower priced 10mm diameter coin vibration motors. We can also add a variety of connectors to the leads. This motor is also available with a flexible printed circuit.


VC0825B029L thumbnail

8 mm x 2.5 mm | 3 V | FPC | Coin Vibration Motor

The VC0825B029L with FPC contact pads is based on the popular leaded version of the same motor, the VC0825B002F.   This device is designed to be mounted in a molded recessed pocket in the products housing.   PCB mounted contact springs or pogo pings mate with coin LRA's contacts pads.   PCBA contact springs are made by TE as well as other companies.  


VC0827B005F thumbnail

8 mm x 2.7 mm | 3 V | Coin Vibration Motor

The VC0827B005F is one of our smallest coin vibration motors. Due to the high degree of manual labor required to assemble this motor and low production yields this motor is relatively expensive. We recommend using this motor only if your design can not accommodate one of our lower cost 10mm or 12mm diameter coin vibration motors. This motor is supplied with a self adhesive tape which can be used to secure the motor to your PCB or the inner wall of your products housing. We can terminate the leads with a variety of connectors. FPC options are also available.


VC0827B307L thumbnail

8 mm x 2.7 mm | 3 V | FPC | Coin Vibration Motor

The VC0827B307L coin vibration motor is based on the popular leaded version of this same motor, the VC0827B005L.   It may be connected to another FPC or by PCB mounted spring contacts.   Custom FPC's based on your design are available. 

 

 


VC0830B001L thumbnail

8 mm x 3 mm | 3 V | Coin Vibration Motor

The VC0830B001L is a brush type coin vibration motor measuring 8mm diam x 3.0 mm in thickness. Can be used in a wide variety of applications requiring a vibration alert feature. Available with custom leads length and connectors.


VC0830B029L thumbnail

8 mm x 3 mm | 3 V | FPC | Coin Vibration Motor

The VC0830B029L coin vibration motor is based on the popular leaded version of this same motor, the VC0830B001L.   It may be connected to another FPC or by PCB mounted spring contacts.   Custom FPC's based on your design are available. 


VC0834B011F thumbnail

8 mm x 3.4 mm | 3 V | Coin Vibration Motor

Our VC0834B011F coin vibrator motor is more costly than our 10 and 12mm diameter motors. We recommend using this coin vibration motor only if your design can not accommodate our lower cost larger diameter motors. This motor is only available with wire leads. At your request, we can add either a Molex or AVX ELCO connector to the end of the leads. Click here for details. Other connectors are available upon request. This motor is supplied with a self adhesive tape which can be used to secure the motor to your PCB or the inner wall of your products housing.


VC1018B001L thumbnail

10 mm x 1.8 mm | 3 V | Coin Vibration Motor

Measuring only 1.8mm thick, the VC1018B001L is currently the thinnest coin vibration motor on the market. Although this version comes with a Poron foam pad on top, it may be ordered without this pad, as well as the double stick tape. If you need this version without the tape or poron foam order VC1018B002L.    Custom wire length and connectors may be added. Minimum orders apply.


VC1020B111F thumbnail

10 mm x 2.1 mm | 3 V | Coin Vibration Motor

Our VC1020B111F  includes an optional 0.2 mm foam pad which helps alleviate unwanted mechanical between the motor and the surface directly above it.  Poron rubber pads of varying thicknesses are available.  This motor is also our most expensive 10mm diameter motor. We recommend using this coin vibration motor only if your design can not accommodate our 2.6, 3.0 or 3.4 mm thick 10mm motors. The price of our 2.6, 3.0 and 3.4 mm thick coin motor are all the same.  This motor is only available with wire leads or we can add a wire-to-board  connector to the end of the leads.  Click here for details.   Other connectors are available upon request.   This motor is supplied with a self adhesive tape which can be used to secure the motor to your PCB or the inner wall of your products housing.


VC1020B327F thumbnail

10 mm x 2.1 mm | 3 V | Connector | Coin Vibration Motor

Our VC1020B327F coin vibration motor is the connectorized version of our popular VC1020B111F.    It uses of the ACES  50270-002H0H0-001   which is based on the popular Molex 78172-0002 series connector.  We favor ACES brand connectors due to their short lead times, quality and price.   Contact them directly, or one of their distributors, for the mating PCB side of this connector.   This motor has the optional 0.2 mm foam pad which helps alleviate unwanted mechanical between the motor and the surface directly above it.  Poron rubber pads of varying thicknesses are available.  This motor is also our most expensive 10mm diameter motor. We recommend using this coin vibration motor only if your design can not accommodate our 2.6, 3.0 or 3.4 mm thick 10mm motors. The price of our 2.6, 3.0 and 3.4 mm thick coin motor are all the same.  This motor is also available with different connectors as well.     Click here for details.   Other connectors are available upon request.   Supplied with a self adhesive tape which can be used to secure the motor to your PCB or the inner wall of your products housing.


VC1020B569L thumbnail

10 mm x 2.1 mm | 3 V | Coin Vibration Motor

The VC1020B569L coin vibration motor is based on the popular leaded version of this same motor, the VC1020B111F.   It may be connected to another FPC or by PCB mounted spring contacts.   Custom FPC's based on your design are available. 

 


VC1026B002F thumbnail

10 mm x 2.7 mm | 3 V | Coin Vibration Motor

The Vybronics VC1026B002F flat vibration motor, is one of our most popular offerings. It combines both a low profile and cost effective pricing. We can add a variety of connectors to the end of the wire leads. Click here for details. If you have a different connector you would like to install, please forward a data sheet to us and we will advise if it is possible for us to connect it during the manufacturing process. This coin vibration motor is supplied with a self adhesive tape which may be used to mount it to your PCB or to the inner wall of your products housing.


VC1026B204L thumbnail

10 mm x 2.7 mm | 3 V | FPC | Coin Vibration Motor

The Vybronics VC1026B204L flat vibration motor is based on our popular VC1026B002F motor which has wire leads.  This motor has large, gold plated, contact pads that are designed to mate with PCB mounted springs or pogo pins. This coin vibration motor is supplied with a self adhesive tape which may be used to mount it to your PCB or to the inner wall of your products housing. If you require this motor, but without the double stick tape on the bottom, please order VC1026B205L.  

 

 

 


VC1027B902F thumbnail

10 mm x 2.7 mm | 3 V | Connector | Coin Vibration Motor

Our VC1027B902F coin vibration motor is the connectorized version of our popular VC1026B002F.    It uses of the ACES  50270-002H0H0-001   which is based on the popular Molex 78172-0002 series connector.  We favor ACES brand connectors due to their short lead times, quality and price.   Contact them directly, or one of their distributors, for the mating PCB side of this connector.   If required, Poron rubber pads of varying thicknesses be be added on request.   Supplied with a self adhesive tape which can be used to secure the motor to your PCB or the inner wall of your products housing. available.    Other connectors or special lead lengths are available upon request.    Click here for details.   


VC1027B923F thumbnail

10 mm x 2.7 mm | 3 V | Connector | Coin Vibration Motor

Our VC1027B923F coin vibration motor is the connectorized version of our popular VC1026B002F.    It uses of the ACES  50276-002H0H0-001   which is based on the popular Molex 51021-0200  series connector.  We favor ACES brand connectors due to their short lead times, quality and price.   Contact them directly, or one of their distributors, for the mating PCB side of this connector.   If required, Poron rubber pads of varying thicknesses be be added on request.   Supplied with a self adhesive tape which can be used to secure the motor to your PCB or the inner wall of your products housing. available.    Other connectors or special lead lengths are available upon request.    Click here for details.   


VC1030A002F thumbnail

10 mm x 3 mm | 1.3 V | Coin Vibration Motor

The VC1030A002F is the low voltage, version of our popular  VC1030B028F.    It may be operated from a single 1.5 V DC  Alkaline battery.   Custom lead wire lengths are also possible, with the shortest length being  8 mm.     For  MOQ:  2000,  a connector may be added to the end of the wires as well.      This coin vibrator motor is supplied with a self adhesive double stick pad which may be used to permanently mount the motor to the PCB or to the wall of your devices housing.   Poron foam pads of various thicknesses may be added as well.  Contact us for a  quote.   


VC1030B028F thumbnail

10 mm x 3 mm | 3 V | Coin Vibration Motor

The Vybronics VC1030B028F coin vibration motor is a popular 3 V leaded design. If requested, we can supply it with a variety of connectors mounted to its wire leads. Click here for details. If you require a different connector to be used, please send us the data sheet and we will advise you if we can connect it. Custom wire lengths are also possible. This coin vibrator motor is supplied with a self adhesive double stick pad which may be used to permanently mount the motor to the PCB or to the wall of your devices housing.


VC1030B295L thumbnail

10 mm x 3 mm | 3 V | transparent | Coin Vibration Motor

The VC1030B295L is housed in a transparent housing to show off its internal workings.  This motor is used as the central design element of the popular Doppel wearable.   It is available in various lead length and connectors may be added to its  wire leads if required.  


VC1030B400U thumbnail

10 mm x 3 mm | 3 V | Coin Vibration Motor

The VC1030B400U coin vibration motor has an FPC with large contact pads that usually mate with PCB mounted pogo-pins or spring contacts on the PCB. Spring contacts are available from many Mfg including TE. This coin vibrator motor is mounted against the inner wall of the product housing. The rear of this motor has 3M 467 double stick tape to facilitate mounting. If the FPC size or contact arrangement is not suitable for your application we can fabricate a custom flexible circuit as per your design. Tooling fees will apply.


VC1030B823L thumbnail

10 mm x 3 mm | 3 V | Coin Vibration Motor

The VC1030B823L coin vibration motor is based on the popular leaded version of this same motor, the VC1030B028F .   It may be connected to another FPC or by PCB mounted spring contacts.   Custom FPC's based on your design are available. 

 


VC1034B018F thumbnail

10 mm x 3.4 mm | 3 V | Coin Vibration Motor

The VC1034B018F is our most powerful 3 Volt 10mm coin vibration motor. We can add a wide range of connectors to its wire leads. Custom lead lengths are also possible. Click here for details. If you require a different connector to be used, send us the data and we will advise you if we can connect it. This coin vibrator motor is supplied with a self adhesive double stick tape pad which can be used to permanently secure the coin motor to the PCB or wall of your devices housing.


VC1034B400D thumbnail

10 mm x 3.4 mm | 3 V | Coin Vibration Motor

The VC1034B400D coin vibration motor has an FPC with large contact pads that usually mate with PCB mounted pogo-pins or spring contacts on the PCB.   Spring contacts are available from many Mfg including TE.  This coin vibrator motor is mounted against the inner wall of the product housing.  The rear of this motor has 3M 467 double stick tape to facilitate mounting. If the FPC size or contact arrangement is not suitable for your application we can fabricate a custom flexible circuit as per your design. Tooling fees will apply.


VC1034B846F thumbnail

10 mm x 3.4 mm | 3 V | Connector | Coin Vibration Motor

Our VC1034B846F coin vibration motor is the connectorized version of our popular VC1034B018F.    It uses an AVX compatible 8005 type connector which also has superior lead times.  Contact us about sources for the PCB side.   If required, Poron rubber pads of varying thicknesses be be added on request.   Supplied with a self adhesive tape which can be used to secure the motor to your PCB or the inner wall of your products housing. available.    Other connectors or special lead lengths are available upon request.    Click here for details.   


VC1034H025L thumbnail

10 mm x 3.4 mm | 1.5 V | Coin Vibration Motor

This coin vibration motor is designed to operate at much lower voltages than the typical motor that operates on 3 Vdc .  These 3 Vdc motors are typically used for devices that use rechargeable LiPo batteries that operate @  3.6 V or higher.   This motor is rated to operate between  1.2  and 1.8 Vdc, making it ideal for devices that use standard AA or AAA batteries that operate @ 1.5 Vdc.  Custom lead lengths and connectors may be added.


VC1234B016F thumbnail

12 mm x 3.4 mm | 3 V | Coin Vibration Motor

Having the largest diameter and thickness, the Vybronics VC1234B016F is our most power coin vibration motor. We can add a wide range of connectors to its wire leads. Custom lead lengths are also possible. Click here for details. If you require a different connector to be used, send us the data and we will advise you if we can connect it. This coin vibrator motor is supplied with a self adhesive double stick tape which can be used to permanently secure the coin motor to the PCB or wall of your devices housing.


VC1434B002U thumbnail

14 mm x 3.4 mm | 3.7 V | Coin Vibration Motor

The VC1434B002U measures 14 mm in diameter,  generates 3 Grms of vibration force, and is our most powerful brush type coin vibration motor.    We can add a wide range of connectors to its wire leads. Custom wire lead lengths are also possible.   Click here for details.  If you need a different connector to be used, send us the data sheet / part # and we will advise you if we can supply it.   This motor is supplied with a  PSA / self adhesive double stick tape pad which can be used to secure the coin motor to the PCB or wall of your devices housing.


VCLP0820B004L thumbnail

8 mm x 2.1 mm | 3 V | Low Current | Coin Vibration Motor

This series of low current coin vibration motor is designed to consume ~ 50% less power than our equivalently sized VC0820B006F. Its ideal for wearable devices with limited battery capacity.  G force and RPM is somewhat lower that the VC0820B006F.  This motor is only available with wire leads. At your request, we can add either a Molex or AVX ELCO connector to the end of the leads. Click here for details. Other connectors are available upon request. This vibration motor is supplied with a self adhesive tape which can be used to secure the motor to your PCB or the inner wall of your products housing.


VCLP1020B002L thumbnail

10 mm x 2 mm | 3 V | Low Current | Coin Vibration Motor

This motor is designed to consume approx. 50% less power and current than our equivalently sized VC1020B111F. G force and RPM is somewhat lower than the VC1020B111F. This motor is only available with wire leads. At your request, we can add a connector to the end of the leads. Click here for details. Other connectors are available upon request. This motor is supplied with a self adhesive tape which can be used to secure the motor to your PCB or the inner wall of your products housing.


VG0825003D thumbnail

8 mm x 2.5 mm | 1.2 Vrms | 240hz | LRA Z-Axis

Our VG0825003D is the smallest LRA coin vibration motor on the market. Its Z-Axis vibration and low current characteristics make it an excellent choice for wearables. It draws only 19 ma @ 0.6 V while producing a G force of 0.45 .  This device utilizes FPC contact pads. These contact pads mate with corresponding PCB mounted spring contacts, that are mounted directly to the  PCB.     A linear resonant actuator driver IC such as the TI DRV2605 is required to drive this device.  Double stick adhesive, &  PORON rubber foam pads are also available options.  Custom FPC are also available for orders of 10K pcs+.


VG0832009L thumbnail

8 mm x 3.2 mm | 1.8 Vrms | 235hz | LRA Z-Axis

The VG0832009L is based on the popular leaded version of this coin LRA, the VG0832008.  This device is designed to be mounted in a molded recessed pocket in the products housing.  PCB mounted contact springs or pogo pings mate with coin LRA's contacts pads.   PCBA contact springs are made by TE as well as other companies.   Customizations will be considered if the project volume is in excess of 100K pcs / year. 


VG0832012 thumbnail

8 mm x 3.2 mm | 1.8 Vrms | 235hz | LRA Z axis

Our VG0832012 LRA coin vibration motor vibrates in the Z axis, which is perpendicular to its largest surface. Its Z axis vibration and low current characteristics make it an excellent choice for wearables. Referring to the table below, it draws only 19 ma @ 0.6 V while producing a G force of 0.55 .  This motor does NOT have double stick tape on the bottom.  If you need this,  order  VG0832013D.  Rubber foam pads, custom lead wire lengths and connectors are available. Custom FPC are also available for orders of 10K pcs+.


VG0832013D thumbnail

8mm x 3.2 mm | 1.8 Vrms | 235hz | LRA Z axis

The VG0832013D LRA coin vibration motor is identical to the VG0832012 except that is has double-stick tape added to facilitate mounting. It vibrates in the Z axis, which is perpendicular to the face of the vibration motor. As seen from the table below, it draws only 19 ma @ 0.6 V while producing a G force of 0.55, making it ideal for battery powered wearables. Rubber Poron foam pads, connectors and custom lead wire lengths are available. Custom FPC are also available for orders of 10K pcs+. If you need this motor, but with longer leads, please consider using the VG0832022D which has 100mm leads.


VG0832019D thumbnail

8 mm x 3.25 mm | 1.8 Vrms | 235hz | LRA Z-Axis

The VG0832019D is the best choice, in this form factor, for haptic feedback applications.  This is a 3rd generation LRA which uses dual-magnet technology for superior rise / fall times of 35 ms / 65 ms maximum.  Actual rise times are faster than stated.  Pricing of this LRA is considerably higher than our other  8 mm  x  3.2 mm LRA's  which all use 2nd generation, single magnet technology.  It is recommended that this device be mounted in a molded recessed pocket in the products housing.  PCB mounted contact springs or pogo pings mate with coin LRA's contacts pads.   PCBA contact springs are made by TE as well as other companies.


VG0832022D thumbnail

8 mm x 3.2 mm | 1.8 Vrms | 235hz | LRA Z axis

The VG0832022D LRA coin vibration motor is identical to the VG0832013D, except that is longer 100 mm wire leads. It vibrates in the Z axis, which is perpendicular to the face of the vibration motor. As seen from the table below, it draws only 19 ma @ 0.6 V while producing a G force of 0.55, making it ideal for battery powered wearables. Rubber Poron foam pads, connectors and custom lead wire lengths are available. Custom FPC are also available for minimum orders of 10K pcs. Tooling fees apply.


VG0832029D thumbnail

8 mm x 3.2 mm | 1.8 Vrms | 205hz | LRA Z axis

The VG0832029D LRA coin vibration motor is identical to the VG0832012 except the VG0832029D has a lower resonant frequency of 205 hz.  Studies have shown that tactile receptors in the skin are more sensitive to lower frequencies, so in theory, a 205 hz LRA such as this will produce a superior haptic feedback experience for the user than a 235 hz LRA.  This LRA oscillates in the Z axis, which is perpendicular to its largest surface.  Its Z axis vibration and low current characteristics make it an excellent choice for wearables. Referring to the table below, it draws only 19 ma @ 0.6 V while producing a G force of 0.55 .  This motor does NOT have double stick tape on the bottom of its case, but it may be specially ordered with this in minimum quantities of 2K pcs.   Rubber foam pads, custom lead wire lengths and connectors are available. Custom FPC are also available for orders of 10K pcs+.


VG0840001D thumbnail

8 mm x 4 mm | 2.0 Vrms | 170hz | LRA Z-Axis

Measuring 8 mm  dia.  x   4 mm thick, the VG0840001D  linear resonant actuator is the largest 8mm diameter LRA on the market producing a minimum vibration force of 1.0  Grms   @  170 hz.   Exceptional rise time of  12 ms (max).    Its small diameter make it ideal for LRA arrays or devices requiring a small diameter LRA.   This LRA is currently used in Samsung's Galaxy Watch6 Smartwatch (Aluminum 46mm).   An LRA Haptic Drive IC must be used to drive this  device.  This  LRA is available with or without wire leads and connectors.     Custom FPC's are available.

 


VG1030001XH thumbnail

10 mm x 3 mm | 2.0 Vrms | 210hz | LRA X-Axis

The VG1030001XH is our first LRA to make use of a new internal structure to generate vibration in the X plane, similar to that of a rectangular LRA.   Please refer to the data sheet that denotes the "direction of vibration" on the mechanical drawing. Rubber Poron foam pads, connectors and custom lead wire lengths are available. Custom FPC are also available for minimum orders of 10K pcs. Tooling fees apply.


VG1036001D thumbnail

10 mm x 3.6 mm | 2.0 Vrms | 175hz | LRA Z axis

The VG1036001D LRA coin vibration motor generates a minimum vibration force of 1.5 Grms @ 175 hz. A driver IC is normally used to generate this AC drive signal. It vibrates in the Z axis, which is perpendicular to the face of the vibration motor, making it ideal for wearable devices worn against the skin. Its excellent rise / fall time specifications make it ideal for haptic feedback applications. Rubber Poron foam pads, connectors and custom lead wire lengths are available. Custom FPC are also available for minimum orders of 10K pcs. Tooling fees apply.


VG1036002D thumbnail

10 mm x 3.6 mm | 2.0 Vrms | 175hz | LRA Z axis

The VG1036002D LRA coin vibration motor is identical to the VG1036001D, but has longer 100mm wire leads. It vibrates in the Z axis, which is perpendicular to the face of the vibration motor. making it ideal for battery powered wearables. Rubber Poron foam pads, connectors and custom lead wire lengths are available. Custom FPC are also available for minimum orders of 10K pcs. Tooling fees apply.


VG1040003D thumbnail

10 mm x 4 mm | 2.5 Vrms | 170hz | LRA Z-Axis

At an impressive 2 Grms the VG1040003D, wide band LRA, produces the highest G force / vibration energy of any coin shaped LRA vibration motor. The rise time is a blazing 10 ms, fall time 50ms, makes it one of the best choices for HD haptic feedback applications.  Notably Samsung chose this LRA for use in their  Galaxy Z Flip 3 and  Samsung Galaxy S21  cellphones.   Due to this LRA's wide bandwidth,  you will need to disable the auto-resonance  calibration feature and manually set the driver for the resonant frequency of the LRA.    Besides the popular TI haptic drivers,  Dongwoon Anatech Part # DW7914A    and the  Renesas (formerly Dialog Semiconductor)  DA728x Series Haptic driver IC are also viable options.   A configuration file is available for the DA728x driver.  This device is designed to be mounted in a molded recessed pocket in the products housing. PCB mounted contact springs or pogo pings mate with coin LRA's contacts pads.   PCBA contact springs are made by TE as well as other companies.    If you need wire leads, you can solder wires to these contact pads, however the wire must be thin and flexible (UL3302  AWG 32 /34) else the adhesive holding the FPC to the metal base may separate and the FPC lift upward.   This motor is currently only available in this configuration. Customizations will be considered if the project volume is in excess of 1 million / year. 


VG2080001-175H thumbnail

20 mm x 8 mm | 1.8 Vrms | 175hz | LRA Z-Axis

The VG2080001-175H linear resonant actuator operates at peak efficiency (3.2 Grms min)  when driven at it resonant frequency of  175 hz .   Its housing has integral mounting flanges.  Custom FPC's or wire leads with connectors may be added on request.    A  Haptic Driver IC  is typically used to provide the AC signal required to drive this LRA.    Contact us for more information. 


VG2080001H thumbnail

20 mm x 8 mm | 1.8 Vrms | 130hz | LRA Z-Axis

The VG2080001H linear resonant actuator operates at peak efficiency (1.8 Grms min)  when driven at it resonant frequency of  130 hz .    It was designed to meet the Automotive industries AEC-Q100 Temperature Grade  3  operating temperature range  of   -40C  to  + 85 C.    Its housing has integral mounting flanges.  Custom FPC's or wire leads with connectors may be added on request.    A  Haptic Driver IC  is typically used to provide the AC signal required to drive this LRA.    Contact us for more information. 

 


VJP12-25F190 thumbnail

10mm Height | 2 ~ 6 V DC | Cylindrical Vibration Motor

This 12 mm vibration motor is available with wire leads or with a variety of connectors. Custom lead lengths are also available for orders over 1000 pcs. These motors are normally used in adult toys, massagers as well as video game controllers.


VJP12-95J100A thumbnail

10mm Height | 1 ~ 4.5 V DC | Cylindrical Vibration Motor

This 12 mm vibration motor is available with wire leads or with a variety of connectors. Custom lead lengths are also available for orders over 1000 pcs. These motors are normally used in adult toys, massagers as well as video game controllers.


VJP12-95J100U thumbnail

10mm Height | 1.5~4.2 V DC | Cylindrical Vibration Motor

This 12 mm vibration motor is available with wire leads or with a variety of connectors. Custom lead lengths are also available for orders over 1000 pcs. These motors are normally used in adult toys, massagers as well as video game controllers.


VLV041235L-FP192 thumbnail

12 x 4 x 3.5 mm | 1.8 Vrms | 240hz | LRA Z-Axis

The  VLV041235L-FP235  is high performance rectangular Linear Resonant Actuator - LRA that can be used for a variety of haptic feedback applications. This device is designed to be mounted on the inner shell of the products housing.  PCB mounted contact springs or pogo pings mate with coin LRA's contacts pads.   PCBA contact springs are made by TE as well as other companies.   Like all LRA's this device is typically connected to a LRA  driver IC which produces the AC  drive signal for this device.  For further information about this see the BOTTOM of this page.   

  Please see photos of how this LRA vibration motor is typically mounted.


VLV041235L-L20 thumbnail

12 x 4 x 3.5 mm | 1.8 Vrms | 240hz | LRA Z-Axis

The  VLV041235L-L20 rectangular, Z-axis LRA can be used for a variety of haptic feedback applications.   This LRA is different than most rectangular LRA's which oscillate in the X plane, along the length of the device.  Like all LRA's this device is typically connected to a LRA  driver IC which produces the AC  drive signal for this device.  For orders of 2K pcs+, we can supply a custom wire length or add one of  connectors or one of your choosing.  


VLV101040A thumbnail

10 x 10 x 4 mm | 2.5 Vrms | 170hz | LRA Z-Axis

The VLV101040A  like our coin type LRA's this device generates a vibration force in the Z axis, perpendicular to the face of the device.    It has an exceptionally wide band width of 160 hz allows for drive signals between 140 to 300 hz.    Wide-band width, coupled with fast 10ms rise/40ms fall times,  allows this LRA to generate haptic effects never before possible.   Even faster rise / fall times can be achieved by the use of a Haptic Driver.    Due to this LRA's wide bandwidth , the use of Haptic drivers  that make use of  "auto -resonance" detection will be problematic ( ie  TI).  If using such a driver, you will need to disable the auto-resonance  calibration feature and manually set the driver for the resonant frequency of the LRA.    The  Dongwoon Anatech Part # DW7914A    and  Renesas (formerly Dialog Semiconductor)  DA728x Series Haptic driver IC are also viable options.   A configuration file is available for the DA728x driver.   The LRA's contact pads are designed for use with PCB mounted pogo pins or spring contacts.   If you need wire leads, you can solder wires to these contact pads, however the wire must be thin and flexible (UL3302  AWG 32 /34) else the adhesive holding the FPC to the metal base may separate and the FPC lift upward. 

 

Please see photos of how this LRA linear vibration motor is typically mounted.

 


VLV221007E thumbnail

22.5 x 10 x 7 mm | 2.3 Vrms | 230hz | LRA Z-Axis

The VLV221007E linear vibration motor / LRA generates 8 Grms  (100 gram sled)  when driven @ 2.35 Vrms.  Possible applications include haptic feedback for gaming, VR & trackpads.  As it is normal for the actual resonant frequency of LRA's to vary +- 10 hz from its rated resonant frequency, to ensure best performance,  it is important to use them with an LRA driver IC that has a closed-loop, auto-resonance tracking mode.   For this LRA we recommend the DA728x series haptic driver by Renesas, as it is the only driver we tested that worked properly in closed-loop, auto-resonance tracking mode.  A Renesas DA728x  Development Board can be purchased here.   In our testing the TI DRV2605L will not pass calibration at the higher rated and over drive clamp voltages, and therefor are unable to drive this LRA at its maximum G force of 8 Grms.  With the TI DRV2605L in closed loop, RTP mode we measured 3.6 Grms.    Custom leads length,  connectorization and custom flexible PCB are available.   


VW0525AB001D thumbnail

5 mm x 2.5 mm | 3 V | BLDC Coin Vibration Motor

At a only 5mm diameter, this is the smallest BLDC brushless coin vibration motor on the market. Its low G force of 0.25 will limit its applications to very light weight wearables such as smart rings and light weight watches etc. Double stick tape on the bottom of the case facilitates mounting. A driver IC is built imbedded within the coin motor. No external driver IC is required. Voltage polarity must be observed or you will damage the internal driver IC.   This device operates on DC voltage only.  A  PWM signal can not be used to drive BLDC motors. MOQ: 2K pcs, we can supply the lead lengths, foam pads of varied thicknesses or a variety of connectors. For MOQ: 10K pcs custom FPC's can be fabricated.


VW0625AB001G thumbnail

6 mm x 2.5 mm | 3 V | BLDC Coin Vibration Motor

The W0625AB01G brushless BLDC coin vibration motor is ideal for Hi-Rel applications or those with high duty cycles. A driver IC is built imbedded within the motor, so no external driver IC is required. Apply DC voltage as you would a normal brushed DC motor. This type of motor is about twice the price of its comparably sized brush type counterpart. If you do not require a Hi-Rel motor, consider using this motor instead. Voltage polarity must be observed or you will damage the internal driver IC. This device operates on DC voltage only. A PWM signal can not be used to drive BLDC motors. For MOQ: 1K pcs, we can supply custom lead lengths as well as connector. For MOQ: 5K pcs custom FPC's can be supplied. 


VW0825AB001G thumbnail

8 mm x 2.5 mm | 3 V | BLDC Coin Vibration Motor

The VW0825AB001G brushless BLDC coin vibration motor is ideal for Hi-Rel applications or those with high duty cycles.  A driver IC is built imbedded within the motor, so no external driver IC is required. Apply DC voltage as you would a normal brushed DC motor. Voltage polarity must be observed or you will damage the internal driver IC. This device operates on DC voltage only. A PWM signal can not be used to drive BLDC motors. For MOQ: 2K pcs, we can supply custom lead lengths as well as connector. For MOQ: 5K pcs custom FPC's can be supplied.


VW0934AB001G thumbnail

9 mm x 3.4 mm | 3 V | BLDC Coin Vibration Motor

Our VW0934AB001G Brushless BLDC coin vibration motor produces 1.4 Grms (avg), which is the highest of any BLDC coin motor we manufacture. Rated for 1,000,00 cycles (min) it is an excellent choice for applications that have a high duty cycle as well as devices that require a very low MTBF / FIT.  A driver IC is integrated within the body of this BLDC vibration motor, allowing it to be powered by DC voltage, like a standard brush type motor.  Voltage polarity must be observed or you will risk damaging the driver IC.  This device operates on DC voltage only. A PWM signal can not be used to drive BLDC motors.  If desired, we can add connectors to the leads as well as supply custom lead lengths.    After sample approval the MOQ is 10,000 pcs


VZ30L4B8560001 thumbnail

3mm Height | 3 V | Wire Leads | Vibration Motor

At a height of just 3 mm the VZ30L4B8560001 is our lowest profile cylindrical vibration motor with wire leads. If your order is for a minimum of 1000 pieces we can add a connector on the end of the wire or supply a custom lead length.


VZ30L4B8790008L thumbnail

3.15mm Height | 3 V | Wire Leads | Vibration Motor

The VZ30L4B8790008L is a leaded version of a  "core type"  motor that we use for our SMD reflow series.  Using this type of motor allowed us to offer a very low profile,  3.15 mm  high,  motor, which would not be possible if we used "coreless technology".   While VZ30L4B8790008L vibration motor has an impressively small form factor, the price is higher than that of a coreless motor.  The 8 mm  lead length shown is the shortest we can supply.  This motor is also available with a rubber boot  which can facilitate mounting. If you need this with a shorter connection we can supply this with a custom FPC.    For MOQ 2000, we can supply this motor with a longer lead length.    Connectorization is also possible for  MOQ: 2000


VZ30L4B8790716L thumbnail

3.7mm Height | 2.4 V | Wire Leads | Vibration Motor

The VZ30L4B8790716L is the leaded version of  the "core type"  motor we use for our SMD reflow series.  Using this type of motor allowed us to offer a very low profile,  with a height of  3.7 mm,  which would not be possible if we used "coreless technology".   While VZ30L4B8790716L vibration motor has an impressively small form factor, the price is higher than that of a coreless motor.  The 8 mm  lead length shown is the shortest we can supply.  If you need a lower profile, you may want to consider this motor, but without the rubber boot.   We can also provide this motor with the same larger counter weight used on this motor.    If you need this with a shorter connection we can supply this with a custom FPC.    For MOQ 2000, we can supply this motor with a longer lead length.    Connectorization is also possible for  MOQ: 2000


VZ32TL2B2882008D thumbnail

3.9mm Height | 3 V | Wire Leads | Vibration Motor

The VZ32TL2B2882008D uses a 3.2 mm diameter coreless motor which is inserted into a silicon rubber sleeve to help facilitate mounting and mitigate unwanted mechanical noise when the motor is actuated.  The 3.2 mm diameter is the smallest diameter coreless vibration motor we offer.  This motor is also without the rubber gasket.  It is avaialble in custom lead lengths as short as 8 mm.   Connectorization is also possible for  MOQ: 2000


4.2mm Hgt | 3 V | Low Current | Spring | Vibration Motor

The VZ3TH5B3120076P is an amazing combination of small size and low power usage, making it ideal for wearables with limited battery capacity.   The rubber gasket helps facilitate mounting in a molded pocket, and mitigate unwanted mechanical noise when the motor is actuated.   It is available in custom lead lengths as short as 8 mm.   Connectorization is also possible for  MOQ: 2000


3.2mm Diameter | 3 V | Low Current | Vibration Motor

The VZ3TL2B3120033P is an amazing combination of small size and low current.  Ideal for wearables with limited battery capacity.    At  3.2 mm it is the smallest diameter motor we make.  This motor is also available with a rubber gasket that help facilitate mounting in a molded pocket, and mitigate unwanted mechanical noise when the motor is actuated.   It is available in custom lead lengths as short as 8 mm.   Connectorization is also possible for  MOQ: 2000


3.8mm Height | 3 V | Low Current | Vibration Motor

The VZ3TL2B3120034P is an amazing combination of small size and low current.  Ideal for wearables with limited battery capacity.    At  3.2 mm it is the smallest diameter motor we make.  The rubber gasket helps facilitate mounting in a molded pocket, and mitigate unwanted mechanical noise when the motor is actuated.   It is available in custom lead lengths as short as 8 mm.   Connectorization is also possible for  MOQ: 2000


VZ4KL2A0030001 thumbnail

4mm Diameter | 1.3 V | Wire Leads | Vibration Motor

The VZ4KL2A0030001 is rated at 1.3 V and is a member of our VZ4KL series of leaded vibration motors. The VZ4KL series is our most powerful 4mm motor series. It is also available with a different counter-weight. See VZ4KL2A0280001. If your order is for a minimum of 1000 pieces we can add a connector on the end of the wire.


VZ4KL2A0280001 thumbnail

4mm Diameter | 1.3 V | Wire Leads | Vibration Motor

The VZ4KL2A0280001 is rated at 1.3 V and is a member of our VZ4KL series of leaded vibration motors. The VZ4KL series is our most powerful 4mm motor series. It is also available with a different counter-weight. See VZ4KL2A0030001. If your order is for a minimum of 1000 pieces we can add a connector on the end.


VZ4KL2B0030001 thumbnail

4mm Diameter | 3 V | Wire Leads | Vibration Motor

The VZ4KL2B0030001 is rated at 3 V and is a member of our VZ4KL series of leaded vibration motors. The VZ4KL series is our most powerful 4mm motor series. It is also available with a different counter-weight. See VZ4KL2B0280001. If your order is for a minimum of 1000 pieces we can add a connector on the end of the wire.


VZ4KL2B0030191 thumbnail

4 mm | 3 V | PCB Mounted Thru-Hole | Vibration Motor

This motor is identical to the VZ4KL2B0030001 but has a PCB mounting bracket. A connector may be added if desired.


VZ4KL2B0030471 thumbnail

5mm Height | 3 V | rubber booth | Vibration Motor

The VZ4KL2B0030471 is our most powerful 4mm diameter that is available with a rubber gasket. The rubber gasket facilities placing this in molded pocket in the shell of your devices housing. This rubber boot may also available for use on any of our VZ4KL series vibration motors. If your order is for a minimum of 1000 pieces we can also add a connector on the end of the wire.

CLICK  HERE to see photos of how this motor is typically mounted in the products housing.


VZ4KL2B0280001 thumbnail

4mm Height | 3 V | Wire Leads | Vibration Motor

The VZ4KL2B0280001 is rated at 3 V and is a member of our VZ4KL series of leaded vibration motors. The VZ4KL series is our most powerful 4mm motor series. It is also available with a different counter-weight. See VZ4KL2B0030001. If your order is for a minimum of 1000 pieces we can add a connector on the end of the wire.


VZ4KL2B0780012P thumbnail

4.6mm Height | 3 V | Low Current | Vibration Motor

The VZ4KL2B0780012P draws 16 ma (typical) @ 3 Vdc, consuming a low 48 milliwatts of power and is supplied in a rubber gasket which is typically used when mounting this low current vibrating motor in a cavity in the devices housing. Contact us if you require this motor without the rubber boot. Custom lead wire lengths are available as are connectors. This series of low power consuming vibration motors are relatively high priced. After sample approval, the minimum order is 3 master cartons, which total 4200 pcs @ USD 2.15 ea

CLICK  HERE to see photos of how this motor is typically mounted in the products housing.


VZ4SL2A0070001 thumbnail

4mm Diameter | 1.3 V | Wire Leads | Vibration Motor

The VZ4SL2A0070001 is rated at 1.3 V and is a member of our VZ4SL series of leaded vibration motors. The VZ4SL series produces less vibration energy than our VZ4KL series, but substantially more than our VZ4TL series. It is also available with different counter-weights. See VZ4SL2A0270001 or VZ4SL2A0280001. If your order is for a minimum of 1000 pieces we can add a connector on the end of the wire.


VZ4SL2A0070131 thumbnail

4 mm | 1.3 V | PCB Mounted Thru-Hole | Vibration Motor

This vibrating motor is identical to our VZ4SL2A0070001, but it has a PCB mounting bracket. The VZ4SL series produces less vibration energy than our VZ4KL series, but substantially more than our VZ4TL series. If your order is for a minimum of 1000 pieces we can add a connector on the end of the wire.


VZ4SL2A0270001 thumbnail

4mm Diameter | 1.3 V | Wire Leads | Vibration Motor

The VZ4SL2A0270001 is rated at 1.3 V and is a member of our VZ4SL series of leaded vibration motors. The VZ4SL series produces less vibration energy than our VZ4KL series, but substantially more than our VZ4TL series. It is also available with different counter-weights. See VZ4SL2A0070001 and VZ4SL2A0280001. If your order is for a minimum of 1000 pieces we can add a connector on the end of the wire.


VZ4SL2A0280001 thumbnail

4mm Diameter | 1.3 V | Wire Leads | Vibration Motor

The vibrator motor is rated at 1.3 V and is a member of our VZ4SL series of leaded vibration motors. The VZ4SL series produces less vibration energy than our VZ4KL series, but substantially more than our VZ4TL series. It is also available with different counter-weights. See VZ4SL2A0070001 and VZ4SL2A0270001. If your order is for a minimum of 1000 pieces we can add a connector on the end of the wire.


VZ4SL2A0280131 thumbnail

4 mm | 1.3 V | PCB Mounted Thru-Hole | Vibration Motor

This motor is identical to our VZ4SL2A0280001, but has a PCB mounting bracket. The VZ4SL series produces less vibration energy than our VZ4KL series, but substantially more than our VZ4TL series. If your order is for a minimum of 1000 pieces we can add a connector on the end of the wire.


VZ4SL2B0070001 thumbnail

4mm Diameter | 3 V | Wire Leads | Vibration Motor

The motor is rated at 3 V and is a member of our VZ4SL series of leaded vibration motors. The VZ4SL series produces less vibration energy than our VZ4KL series, but substantially more than our VZ4TL series. It is also available with a different counter-weight. See VZ4SL2B0280001. If your order is for a minimum of 1000 pieces we can add a connector on the end of the wire.


VZ4SL2B0270131 thumbnail

4 mm | 3 V | PCB Mounted Thru-Hole | Vibration Motor

This motor is identical to our VZ4SL2B0270001, but it has a PCB mounting bracket. The VZ4SL series produces less vibration energy than our VZ4KL series, but substantially more than our VZ4TL series. If your order is for a minimum of 1000 pieces we can add a connector on the end of the wire.


VZ4SL2B0280001 thumbnail

4mm Diameter | 3 V | Wire Leads | Vibration Motor

The VZ4SLB02800001 is rated at 3 V and is a member of our VZ4SL series of leaded vibration motors. The VZ4SL series produces less vibration energy than our VZ4KL series, but substantially more than our VZ4TL series. It is also available with a different counter-weight. See VZ4SL2B0070001. If your order is for a minimum of 1000 pieces we can add a connector on the end of the wire.


VZ4SL2B0280131 thumbnail

4 mm | 3 V | PCB Mounted Thru-Hole | Vibration Motor

This 4mm diameter motor is identical to our VZ4SL2B0280001, but it has a PCB mounting bracket. The VZ4SL series produces less vibration energy than our VZ4KL series, but substantially more than our VZ4TL series. If your order is for a minimum of 1000 pieces we can add a connector on the end of the wire.


VZ4TC2B0640001P thumbnail

4mm Diameter | 3 V | Low Current | Vibration Motor

At less than 10mm in overall length, the VZ4TC2B0640001P is the smallest vibration motor is our low current series.  It draws 17 ma (typical) @  3 Vdc, consuming a low  51 milliwatts of electrical energy.  If you require this motor with a  rubber boot order VZ4TC2B0640002P.   This boot is highly recommended when mounting this low current vibration motor in a cavity in the  products housing.  Custom lead wire lengths are available as are connectors.    This series of  low power consuming vibration motors are relatively high priced.  After sample approval, the minimum order is 3 master cartons, which total  4800 pcs @  USD  2.15 ea


VZ4TC2B0640002P thumbnail

4.6mm Height | 3 V | Low Current | Vibration Motor

At less than 10mm in overall length, the VZ4TC2B0640002P is the smallest vibration motor is our low current series.  It draws 17 ma (typical) @  3 Vdc, consuming a low  51 milliwatts of electrical energy.  If you require this motor without the  rubber boot order VZ4TC2B0640001P.   This boot is recommended when mounting this low current vibrating motor in a cavity in the devices housing.  Custom lead wire lengths are available as are connectors.    This series of  low power consuming vibration motors are relatively high priced.  After sample approval, the minimum order is 3 master cartons, which total  4200 pcs @  USD  2.30 ea

CLICK  HERE to see photos of how this motor is typically mounted in the products housing.


VZ4TJ1B0020001 thumbnail

4mm Diameter | 3 V | With Connector | Vibration Motor

This 4mm motor is identical to our VZ4TL2B0020011 but we have added our AVX ELCO 8005 series connector to the lead wires of the vibration motor. Other connector options are available.


5mm Height | 3 V | With Connector | Vibration Motor

This motor is identical to our VZ4TL2B0020011 but we have added our AVX ELCO 8005 series connector to the lead wires and a rubber boot. Other connector options are available for this vibration motor.


VZ4TL2B0020001 thumbnail

4mm Diameter | 3 V | Wire Leads | Vibration Motor

The VZ4TL2B0020001 is a member of the VZ4TL family of vibration motors and is the smallest 4mm leaded motor we manufacture. If your order is for a minimum of 1000 pieces we can add a connector on the end of the wire.


VZ4TL2B0020011 thumbnail

5mm Height | 3 V | Wire Leads | Vibration Motor

This motor is identical to our VZ4TL2B0020001, however it has a has a silicone rubber boot running the length of the motor. This boot allows the motor to be press fit into a cavity in your products housing. You may request that this rubber boot be added to any of our VZ4TL family of vibration motors. If your order is for a minimum of 1000 pieces we can mount a connector on the end of the wire.

CLICK  HERE to see photos of how this motor is typically mounted in the products housing.

 


4mm Diameter | 3 V | Low Current | Vibration Motor

The VZ4TL2B0370032L low power / low current consumption vibration motor is the same motor used on our discontinued VZ4TL2B03715452, but minus the PCB mounting bracket.  Its available with custom lead lengths and connectors as well.


VZ4TL2B0370055L thumbnail

4mm Diameter | 3 V | Low Current | Vibration Motor

This is a special 4mm vibration motor designed for low current / low power consumption.  It is normally mounted in a molded pocket in the shell of the products housing.   This motor is available with or without the PCB mounting bracket and is also available.  For minimum orders of 2000 pieces we can add a connector on the end of the wires.    If you need this motor without the rubber gasket please order VZ4TL2B0370032L  ( 17mm  leads )

CLICK  HERE to see photos of how this motor is typically mounted in the products housing.


VZ4TL2B03715452 thumbnail

4 mm | 3 V | Low Current | Thru-Hole | Vibration Motor

This is a special 4mm vibration motor designed for low current / low power consumption. This motor is available with or without the PCB mounting bracket and is also available with a silicone rubber sleeve as well. For minimum orders of 1000 pieces we can add a connector on the end of the wires. NOTE: Although we do have samples of this motor in stock, our tooling for the PCB bracket needs to be replaced and there is currently no demand for this bracket to justify making a replacement tool. If you interested in using this configuration in your design please contact us to discuss this issue.    If you need this motor without the PCB bracket order VZ4TL2B0370032L  ( 17mm  leads )


VZ4TL2B037154E thumbnail

4 mm | 3 V | PCB Mounted Thru-Hole | Vibration Motor

This vibrator motor offer the largest counter-weight available in the VZ4TL series and also incorporates a PCB mounting bracket. If your order is for a minimum of 1000 pieces we can add a connector on the end of the wire. NOTE: Although we do have samples of this motor in stock, our tooling for the PCB bracket needs to be replaced and there is currently no demand for this bracket to justify making a replacement tool. If you interested in using this configuration in your design, please contact us to discuss this issue.


VZ4TL2B0620043P thumbnail

4mm Diameter | 3 V | Low Current | Vibration Motor

The VZ4TL2B0620043P is the most efficient vibration motor we offer.  It draws a remarkably low current of 9 ma (typical) @  3 Vdc while generating a vibration force of 0.75 Gpk.   Energy consumption is a mere 27 mw.  If you require this motor with the rubber boot order VZ4TL2B0620044P.  This rubber gasket is recommended when mounting this motor within a recessed cavity in the device and will minimize unwanted mechanical noise and ensure maximum transfer of vibration energy to the products housing.   Custom lead wire lengths are available as are connectors.    This series of  low current vibration motors are relatively high priced.  After sample approval, the minimum order is 1 master carton of 4800 pcs @  USD  2.15 ea


VZ4TL2B0620044P thumbnail

4.7mm Height | 3 V | Low Current | Vibration Motor

The VZ4TL2B0620044P is the most efficient vibration motor we offer.  It draws a remarkably low current of 9 ma (typical) @  3 Vdc while generating a vibration force of 0.75 Gpk.   Energy consumption is a mere 27 mw.  If you require this motor without the rubber boot order VZ4TL2B0620043P .   Custom lead wire lengths are available as are connectors.    This series of  low current vibration motors are relatively high priced.  After sample approval, the minimum order is 1 master carton of 3520 pcs @  USD  2.15 ea

CLICK  HERE to see photos of how this motor is typically mounted in the products housing.


VZ4TL2B124064X thumbnail

4.6mm Height | 3 V | Wire Leads | Vibration Motor

This motor is similar to other VZ4TL series motors, but it our uses a smaller counter weight. The silicone rubber boot running the length of the motor allows the motor to be press fit into a cavity in your products housing. You may request that this rubber boot be added to any of our VZ4TL family of vibration motors. If your order is for a minimum of 1000 pieces we can mount a connector on the end of the wire.

CLICK  HERE to see photos of how this motor is typically mounted in the products housing.


VZ6CL2A0540722 thumbnail

7.8 mm | 1.3 V | Water Resistant | Vibration Motor

The VZ6CL2A0540722 water resistant motor vibration motor is ideal for imbedding into an object or in any environment where there is a possibility that something might impede the free movement of the counter weight. If your order is for a minimum of 1000 pieces we can add a connector on the end of the wire.


VZ6DC1B0050091 thumbnail

6 mm | 3 V | PCB Mounted Thru Hole | Vibration Motor

The motor is a member of our popular VZ6D series of vibration motors. Our VZ6D series generates less vibration energy than our VZ6CL series but more than the smaller VZ6S series of motors. If your order is for a minimum of 1000 pieces we can mount a connector on the end of the wire.

Please read our special soldering guidelines for this part.


VZ6DL2A0050001 thumbnail

6mm Diameter | 1.3 V | Wire Leads | Vibration Motor

This motor is a member of our popular VZ6D series of vibration motors. Our VZ6D series generates less vibration energy than our VZ6CL series but more than the smaller VZ6S series of vibration motors. If your order is for a minimum of 1000 pieces we can mount a connector on the end of the wire.


VZ6DL2A0050441 thumbnail

6 mm | 1.3 V | PCB Mount Thru Hole | Vibration Motor

This motor is identical to our VZ6DL2A0050001 vibrator motor but with a through-hole PCB mounting bracket. Its also available with a connector mounted on the leads.


VZ6DL2A0170001 thumbnail

6mm Diameter | 1.3 V | Wire Leads | Vibration Motor

Our VZ6DL2A0170001 is a member of our very popular VZ6D series of vibration motors. The VZ6D series generates less G force than our VZ6CL series but substantially more than the smaller VZ6S series of motors. If your order is for a minimum of 1000 pieces we can add a connector on the end of the wire.


VZ6DL2A0765217 thumbnail

7 mm | 1.3 V | Water Resistant | Vibration Motor

This vibration motor is encapsulated in a nickel plated metal capsule making it suitable for over mould applications. Due to the glue sealed cap on the rear of the capsule, this motor is far more resistant to liquid penetration than motors that use our plastic capsule. If your order is for a minimum of 1000 pieces we can add a connector on the end of the wire.


VZ6DL2B0050001 thumbnail

6mm Diameter | 3 V | Wire Leads | Vibration Motor

The VZ6DL2B0050001 is a member of our very popular VZ6D series of 6mm diameter vibration motors. The VZ6D series generates less G force than our VZ6CL series but substantially more than the smaller VZ6S series of motors. If your order is for a minimum of 1000 pieces we can add a connector on the end of the wire.


VZ6DL2B0050441 thumbnail

6 mm | 3 V | PCB Mount Thru Hole | Vibration Motor

This motor is identical to our VZ6DL2B0050001 vibrator motor but with a through-hole PCB mounting bracket. Its also available with a connector mounted on the leads.


VZ6DL2B0055211 thumbnail

7 mm | 3 V | Water Resistant | Vibration Motor

Our VZ6DL2B0055211 vibration motor is ideal for over mold applications. Due to the glue sealed cap on the rear of the capsule, this motor is far more resistant to liquid penetration than motors that use our plastic capsule. As of this time, we do not have an IS or IP rating for any of our parts.  your order is for a minimum of 1000 pieces we can add a connector on the end of the wires.


VZ6DL2B0541192 thumbnail

6.7mm Height | 3 V | Wire Leads | Vibration Motor

This vibrator motor has a rubber boot that run the length of the motor. This silicone boot is available for use on any of our VZ6DL series motors. Please call for details. For orders of 1000 pieces we can add a connector to end of the wire.

CLICK  HERE to see photos of how this motor is typically mounted in the products housing.

 


VZ6DL2H0125215 thumbnail

7 mm | 1.5 V | Water Resistant | Vibration Motor

This encapsulated vibration motor use a nickel plated metal capsule making it perfect for over mold applications. The cap on the rear of the capsule make this motor far more water proof than vibration motors that use our plastic capsule. If your order is for a minimum of 1000 pieces we can add a connector on the end of the wire.


VZ6SL2A0060001 thumbnail

6mm Diameter | 1.3 V | Wire Leads | Vibration Motor

This motor is a member of our very popular VZ6S series of vibration motors. The VZ6S series is our smallest 6mm motor. For orders of 1000 pieces we can add a connector to the end of the wire.


VZ6SL2A0120001 thumbnail

6mm Diameter | 1.3 V | Wire Leads | Vibration Motor

The VZ6SL2A0120001 is a member of our very popular VZ6S series of vibration motors. The VZ6S series is our smallest 6mm motor. For orders of 1000 pieces we can add a connector to the end of the wire.


VZ6SL2B0060001 thumbnail

6mm Diameter | 3 V | Wire Leads | Vibration Motor

This vibration motor is a member of our popular VZ6S series. The VZ6S series is our smallest 6mm diameter motor. For orders of 1000 pieces we can add a connector to the end of the wire.


VZ6SL2B0120001 thumbnail

6mm Diameter | 3 V | Wire Leads | Vibration Motor

The VZ6SL2B0120001 is a member of our popular VZ6S series of vibrator motors. The VZ6S series is our smallest 6mm diameter motor. For orders of 1000 pieces we can add a connector to the end of the wire.


VZ6SL2B0760002 thumbnail

6mm Diameter | 3 V | Wire Leads | Vibration Motor

The VZ6SL2B0760002 ERM vibration motor has a small profile but generates 2.8 G of vibration force.  A PCB mounting bracket is also available for this motor.  Custom lead length and connectorization is also available for MOQ: 2000.  


VZ7AJ2B1692081 thumbnail

8.8 mm | 3 V | Water Resistant | Vibration Motor

The VZ7AJ2B1692081 is a connectorized version of our popular VZ7AL2B1692082 .    Wire leads  are terminated with a  JST  PHR-2 connector.    Other connector types and lead length are available upon request.  

 


VZ7AV2K0760001C thumbnail
VZ7AV2K0760001C

Product is EOL

7mm Diameter | 12 V | Automotive | Vibration Motor

The VZ7AV2K0760001C is an Automotive Grade vibration motor that meets AEC-Q100 Temperature Grade specifications.  These are typically used in steering wheels, gear shifters or any surface that a driver may interact with that requires haptic feedback.    Current  4Q 2022  Price:   MOQ:  5K  @  USD  7.50 ea     .  We can supply this motor with any lead length or with connectors.  


VZ7AV2K0760001L thumbnail

7mm Diameter | 5 V | Automotive | Vibration Motor

The VZ7AV2K0760001L is an Automotive Grade vibration motor that meets AEC-Q100 Temperature Grade specifications.  These are typically used in steering wheels, gear shifters, within the seat or any surface that a driver may interact with that requires haptic feedback.    Current   2023  Price:   MOQ: 2K  @  USD  3.90 ea     .  We can supply this motor with any lead length or with an alternate connector.  


Top